12V 52Ah Lead Acid Deep Cycle Battery for Texlift US-TX SC16 Floor Scrubber

The US-TX SC16 12V 52Ah Lead Acid Deep Cycle Battery is a replacement rechargeable battery designed for the electrical power system of compatible Texlift SC16 floor scrubbers.

The battery provides rechargeable electrical energy to support normal floor scrubber operation, cleaning performance, and the electrical power requirements of compatible equipment.

This replacement battery is designed for compatible Texlift US-TX SC16 floor scrubbers equipped with the corresponding 24V lead acid battery system. Machine configurations can vary, so compatibility should be verified before ordering.

Yes. The battery is designed as a replacement for a compatible original 12V 52Ah lead acid battery used in supported US-TX SC16 floor scrubbers.

This product includes 1 individual 12V 52Ah Lead Acid Deep Cycle Battery. The listed price applies to one battery, not a complete two-battery set.

The Texlift US-TX SC16 Floor Scrubber requires 2 × 12V 52Ah lead acid batteries connected in series to provide its complete 24V electrical system.

For a complete battery replacement, we strongly recommend purchasing 2 matching batteries together. This helps support balanced charging, consistent electrical performance, and reliable operation. Select quantity 2 before checkout if replacing both batteries.

Replacing one battery may be possible when the remaining battery is compatible and in suitable condition. However, replacing both batteries together is generally recommended when the existing battery set is aged or deteriorated to help prevent uneven charging and discharge performance.

Each battery has a nominal voltage of 12V and a rated capacity of 52Ah, providing approximately 624Wh of nominal electrical energy.

The Texlift SC16 uses two 12V 52Ah lead acid batteries connected in series to create a 24V 52Ah electrical system with approximately 1,248Wh of nominal energy.

This is a sealed valve-regulated lead acid Deep Cycle Battery with AGM GEL technology as identified by the manufacturer. It is designed for repeated charging and discharging in compatible electrical equipment.

The manufacturer specifies a standby charging voltage of 13.6–13.8V, a cycle charging voltage of 14.4–14.8V, and a maximum initial charging current of 15.6A per battery at 25°C (77°F). Use charging equipment compatible with the complete battery system.

Battery runtime depends on the floor scrubber's operating conditions, cleaning intensity, battery condition, equipment settings, and maintenance. Actual operating time may vary between applications.

Replace the battery when it is damaged, excessively worn, unable to maintain a sufficient charge, or no longer provides reliable operating performance. Inspect the charging system and electrical connections before determining whether replacement is necessary.

The SC16 uses two batteries together in one electrical system. Installing two matching batteries of the same voltage, capacity, chemistry, and similar condition helps support balanced charging and discharging and may improve overall battery system reliability.

The red terminal identifies the positive (+) connection, while the blue terminal identifies the negative (−) connection. Always verify polarity markings before installation to prevent incorrect electrical connections.

No. Stop operating the floor scrubber when the battery charge level reaches 20% or below. Recharge the batteries using a compatible charger before continuing operation to help prevent excessive discharge and premature battery deterioration.

We recommend maintaining the battery charge level above 40% whenever possible to support battery performance and service life. Stop operation and recharge when the charge level reaches 20% or below.

The battery should be inspected periodically for physical damage, loose terminals, corrosion, overheating, and reduced charging performance. Follow the manufacturer's charging, handling, and storage instructions.

Power off and safely secure the floor scrubber, disconnect the charger, and follow the manufacturer's battery replacement procedures. Remove the existing battery, install the compatible replacement, verify correct terminal polarity, and secure all electrical connections. Installation should be performed by qualified personnel.

Verify that the battery is securely installed, the positive and negative terminals are correctly connected, the complete 24V battery system is properly configured, and there are no loose cables, damaged connections, or charging problems before returning the floor scrubber to service.

No. The 12V 52Ah Lead Acid Deep Cycle Battery is not a universal replacement for all floor scrubbers. It is intended for compatible Texlift SC16 configurations with matching electrical specifications, dimensions, terminals, and charging requirements.

Yes. The battery includes a 90-Day Replacement Parts Warranty covering eligible manufacturing defects under normal intended use. Normal battery aging, capacity loss from routine use, improper charging, misuse, and incompatible installation are not covered.

Verify your floor scrubber model and compare the existing battery's voltage, capacity, dimensions, terminal configuration, and installation requirements. If you are unsure, send Texlift the machine model, serial number, and clear photos of the existing battery and electrical connections.

Yes. Texlift can assist with replacement battery identification and compatibility verification. Providing the equipment model, serial number, and clear photos of the existing battery label, terminals, and installation location helps ensure accurate part identification.